Step Wise Guide for Canon Pixma mg3000 Troubleshooting

How to resolve Canon Pixma Printing errors using troubleshooting methods?

The best and easy way to resolve Canon Pixma error fix with your Canon printer is to get your Canon printer service. Undoubtedly, Canon Pixma printer is the most versatile and serves the best operations. It is well known for its performance. However, being an electronic device, it also comes across a few errors in regards to its functionality which can be easily taken care of using effective techniques. We are hereby mentioning most common errors faced while using a Canon Pixma printer along with the methods to Canon Pixma mg3000 troubleshooting steps. This is most severely known issue wherein your Canon Pixma printer keep printing blank pages. Here are steps below to tackle these issues:

• The first step is that you need to make sure that ink cartridges which you are using with your Canon Pixma printer must be compatible with your printer and quality of cartridges being used with the Canon printer must be good quality.
• Ensure that your printer should not be placed on a hot surface.
• Using your system, clean printhead of your Canon Pixma printer.
• Open my computer on your system.
• Visit Control Panel and move to My Devices and Printers.
• Right-click on the Canon Pixma printer model and visit the properties tab.
• You need to make sure that the correct Device setting must be set inside the Properties tab.
• Now choose the Preferences and hit on Services. Afterward, choose the Clean Printhead tab.
• Keep on proceeding with upcoming instructions on the screen and continue till the time printhead gets cleaned properly.
• Proceed with printing a test page just to ensure that blank pages errors have been resolved or not. Alternatively, select to enable the Skip Blank Page option on your system to avoid the problem.

If after following above-mentioned steps, the issue still persists, then you need to take expert advice; hence, Contact Canon Technical Support at 1-855-800-3376 and get you to issue resolved by dedicated professionals.

Canon Pimxa Mg3000 Printer is unable to print wirelessly

• To begin with, restart all of your devices i.e. Canon Pixma printer, your computer and your router.
• Now, switch on your Canon printer ON and wait at least for 10 seconds before proceeding further.
• Take off power cable from your printer and check is issue still persists.
• Hold on for at least 10 seconds and then put the power cable back into socket.
• Now switch on your device and check printing a document and see whether issue has been resolved or not.
• If issue still persists, then once clear print queue using your computer to solve the issue.
• Despite of all the above mentioned steps, even is the issue persists, then it may indicate towards corruption of your drivers. Now you need to uninstall and reinstall the printer drivers once again on your system.

Canon Pixma printer is unable to print Black

• This is problem which generally occur due to clogged nozzles. This can be simply resolved by cleaning the nozzles.
• Ensure a good number of printing paper sheets in paper tray.
• Try raising the paper output tray and its extension.
• You can initiate cleaning process by clicking on the Setup button on the operator panel of your Canon Pixma printer.
• Now hit Tools button followed by Maintenance option.
• Nor press OK button, afterwards hit Deep Cleaning tab. Now press OK one more time.
• To confirm cleaning hit Ok Tab.
• One more time hit OK tab and do not proceed further until the complete cleaning process is finished up.
• It may take three to five minutes to end up with this process,
• When you see The Pattern Print Confirmation dialog box. Press OK.
• If after doing above steps, you still see that issue is not resolved, do remember to check level of Ink into your black ink cartridge.

Why is my Canon Pixma printer not responding? Despite being the best printing devices company in the world, People often get stuck with various error messages and problems with the Canon printers. The most common issues that have been reported by the users are ‘Canon printer not responding. If you are also one of them and continue getting the pop error message saying “Canon printer not responding” then there is nothing to panic. This issue may occur due to numerous reasons and causes. Below are the general reasons:

• When the user forgets to plug-in the power cable
• False setting on the system while installation procedure of printer device
• Mechanical glitches inside the Canon printer device
• When the printer located on the network is inappropriately connected.

There can be several reasons and similarly, several solutions are there as well. To know how to get a hold of this issue and know the root cause of your Canon printer not responding, continue with this life-saving article. How to Fix Canon Printer Not Responding Error?

Solution No. 1 In the case of Canon Wireless Printer Not Responding

At times when the printer is connected to the system wirelessly, chances are that the printer may not respond due to a communication problem. To diagnose this issue, make sure to stick to these steps:

• Press the Setup button of your Canon printer
• Now, go to the “Wireless LAN” setup and press “OK”

• Select “Easy Setup” and press “OK” again

• Go for the Access point

• Next, enter the WiFi password and press “OK”

• Insert the Setup disk in the computer

Solution No. 2 Turn the Network Discovery ON

Most of the time, the printer is not responding because of the network issue it has been facing. To gid rid of this issue, keep a check on the network as it is the network that enables the system to see other devices connected to it.

• Select the Start button on the extreme left bottom of your screen
• Now click on the Control Panel

• Select the Network and Internet

• Now select “Network and Sharing Centre”
• After that choose “Advanced Sharing settings”
• In case the Network Discovery is turned OFF, click on the radio button to turn the Network discovery ON.

Solution No. 3 Keep a check on the Printer Spooler Service

The print spooler service is responsible for managing all the print jobs that are sent to the printer of the computer. If the service is disabled, the printer will not receive the commands and will not work eventually. Though the printer service is visible to the users and the print job lined up can also be canceled by the user itself to manage the print task.

• Click on the Start menu on the screen
• Type Services in the search box opened
• Select the Print Spooler option
• And then select properties
• Now enable the print service

Solution No. 4  Disable the third-party firewall or the security suite

An overprotective firewall often generates the issue where the printer stops responding. Though the inbuilt solution is quite unrestrictive but the third-party antivirus suites like McAffee, Avira, AVG, etc are considered to create such problems. So many users say that they have encountered this issue and reported that their antivirus solution ended up blocking the spooler subsystem app which made the wireless connection incurable.

Solution No. 5 Use the printer troubleshooter:

The troubleshooter of windows is generally known for being unhelpful in such cases but it has helped quite a few people and you never know it can be helpful to be you as well. You need to keep the following steps in head to configure the issue of “Printer not responding”.

• Press Windows key + R to open up a Run Box.
• Type “control.exe /name Microsoft.Troubleshooting”

• Press “Enter” to open Windows Troubleshoot.
• Once the troubleshoot s up, scroll down and select “Printer’
• Now click on “Run the troubleshooter”
• After this, the troubleshooter will detect the problem and reflect it on the screen
• If there is any inconsistency found, then you will be asked to follow repair strategies

• Now you just need to restart the computer and see if the issue is resolved.

Solution No. 6    Change the USB port

If you are receiving a constant message of “Canon printer not responding” on your system then there might be an issue with the USB connected to it. At times, we make such innocent mistakes of not checking these minor facts. It is possible that the USB is completely fine but the port in which it is connected is not working properly. It is advisable to switch the port once. Do the following steps once and see if you get rid of the issue:

• open a Run box (Windows key + R)
• type “devmgmt.msc”

• Press “Enter” to open Device Manager.
• Expand the drop-down menu associated with the Universal Serial Bus controller
• Find the exclamation points near the icons.
• Right-click on the associated entry
• choose Uninstall device if you find any occurrence

The methods mentioned above consist of the most efficient and easier steps that will definitely fix the Canon mx922 printer not responding but, in case the aforementioned solutions did not help then you may have to get in touch with the professionals.