settembre 2021 - car diagnostic tool

How to Solve Scania SDP3 cannot Find Any SOPS file with Empty

This post show you guide on how to solve Scania SDP3 diagnostic software can’t establish contact with the vehicle.When the program is started, a fault message appears indicating that the program cannot find any SOPS file. When you enter the program, it is empty.

Procedures:

1.Check that the VCI is connected.

Function of the lamps
PWR (green) The lamp is constantly on when Scania VCI-3 is supplied with power.
VCI2: The lamp flashes when the VCI is connected to the PC.
CAN (yellow) The light lights up (flashes rapidly) when data is transmitted between the VCI and the vehicle via the CAN bus.

Error (red) The lamp lights up when there is a communication error on the CAN bus.

VCI2: USB (yellow)
The lamp lights up (flashes rapidly) when data is transmitted between the PC and VCI via the USB key.

VCI3: Info (orange)
The lamp flashes rapidly when general information is sent between the computer and VCI3.

VCI3: WLAN (blue)
The lamp is on or flashes when VCI3 is connected to a local network via wireless connection in one of the following ways: The lamp is constantly on when it is connected to a computer via a wireless network with a good signal strength. The lamp flashes slowly and steadily when VCI3 does not have contact with the computer but is connected to a wireless network with a good signal strength. The lamp flashes once per second if there is a fault during startup

2.Try to start the program again.
3.Check using the IVD function on the instrument cluster (diagnostic mode) that the ICL control unit can communicate with systems on the green CAN bus.
Note:On low-specification vehicles, it is not certain that there will be any systems on the green CAN bus.
Check via the instrument cluster which systems should be available on the vehicle and compare them with the CAN chart on the last page.
•If the ICL control unit has established contact with the green CAN bus, check whether there is an open circuit somewhere between the VCI2/VCI3 and the junction block for the green CAN bus (C479).
•If the ICL control unit has not established contact with the green CAN bus, continue troubleshooting as follows:

The junction blocks are concealed and located on the right-hand side of the central electric unit area. They are fitted in the holes without locking, which means that they can easily be taken out.

1.Switch on the voltage and measure the voltage level between chassis ground and the green CAN bus using a multimeter.
– The voltage should be approx. 2.5 V. You can measure on both CAN-high and CAN-low.

Note:
During the following measurement, all systems must be connected but not supplied with voltage.
2.Measure the resistance on the CAN cable between CAN high and CAN low.
– The resistance should be 54-60 ohm.
3.Measure the resistance between CAN high and chassis ground or between CAN low and chassis ground to check that the resistance is high enough.
– The resistance must be in the order of a megaohm or more. In most cases it is much more.
4.If the resistance is too low, take the switch apart and measure on the junction block for the green CAN bus for all cables in order to find out which control unit is faulty.
5.Disconnect the control unit concerned in order to determine whether there is a fault on the control unit or in the cable harness.
6.If there is a fault in the cable harness, troubleshoot according to the instructions set out in the document Electrical system in P,R and T series, Introduction and general troubleshooting.

https://truckscantool.blogspot.com/2021/08/how-to-solve-scania-sdp3-cannot-find.html

How to Program BMW ECU Online by XTOOL H6 PRO

XTOOL A80 PRO (same as H6 Pro) the ECU programming device can work for VW / BMW / BENZ / FORD / MAZDA / AUDI. Here brings you a demo on BMW X3 2015 online ECU (Seat memory, driver) programming by A80 PRO.

Connect XTOOL A80 PRO to vehicle as the diagram and to the network.

On homepage, press

Diagnosis>>Europe>>BMW

After firmware downloading, select “Automatic selection” and confirm vehicle information.

Now on the main menu, press “Programming/Coding”.

Here we can also refer to the diagram.

Press “Next” and confirm vehicle info. again.

After configuration, we enter the system list.

Choose “Seat memory, driver” and “Programming and coding” to start downloading programming file.

Follow and watch the prompts.

The process may cost 5mins or more.

Programming and coding success.

Done！

This is the process of “Seat memory, driver” programming and coding for BMW X3 2015 by XTOOL H6 PRO.

Which Xtool Tablet Can Learn Key for VW Sharan 2012 ID48-A1

One customer asked:

I want to do key learning on my VW Sharan 2012 ID48-A1. Which Xtool key programmer can do it?

Obd2tool.com engineer answered:

The car model belongs to 4th Immobilizer system. For VW 4th and 5th immobilizer, you should use the following devices.

XTOOL X100 PAD2 Pro (comes with KC100 adapter)

XTOOL X100 PAD3 (comes with KC100 adapter)

XTOOL X100 PAD3 SE and adapter (optional)

Note: Because x100 pad key programmer is not compatible with kc100 adapter, so it cannot support the function.

How to Use KC100 with X100 Pad2/X100 Pad3/X100 PAD3 SE for 4th and 5th immobilizer:

Let’s take X100 PAD3 as an example. Since VW 4th and 5th Immo programming needs online programming, please make sure X100 PAD3 connect Internet before doing programming.

Operation steps:
1.Use the main cable and OBDII connector (or other relative connector) to connect between X100PAD3 and your car’s OBD port
2.Use USB to mini USB cable to connect between X100PAD3 and KC100
3.Switch ignition on position, then enter software as following steps:
Immobilization>> VW>> 4th/5th Immobilizer System

4.If your car is 4th immobilizer system, please click 4th immobilizer system.

If your car is 5th immobilizer system, please click 5th immobilizer system.

It will detect your meter type automatically, if it does not detect successfully, you can choose your meter type manually.

5.Then follow the instructions that software reminds you to copy new keys

For your convenience, here is the related car list for VW immobilizer.

It applies to X100 PAD2 Pro/X100 PAD3/X100 PAD3 SE.

VOLKSWAGEN Function menu V28.07
Car series	System type	Include car models	Function menu
VW	Diagnostic function	AUDI	1). 01 Engine2). 09 Central control3). 17 Dashboard4). 25 Immobiliser 5). 35 Central lock 6). 46 Central comfort module 7). 02 Automatic transmission 8). 03 Anti-lock brakes 9). 08 Automatic air conditioning 10). 15 Airbag 11). 16 Steering wheel 12). 19 Gateway can 13). 44 Power Steering 14). 53 Parking Brake 15). 55 Xenon lamp 16). 56 Radio 17). 76 Parking Aid
		SKODA
		VW
		BENTLEY
		SEAT
	Read security code	AUDI	1). 17 Dashboard1.1). CANDY(3.5th)1.2). LAVIDA (3.5th) 1.3). SAGITAR (3.5th) 1.4). T0URAN (3.5th)2). 25 Immobiliser 3). 01 Engine 3.1). SANTANA VISTA 3.2). LAVIDA 3.3). TOUAREG (03-07) 3.4). BEETLE 3.4.1). Type 1(-2006) 3.4.2). Type 2(2007-) 3.5). Others
		SKODA
		VW
		BENTLEY
		SEAT
	Program keys	AUDI	1). 17 Dashboard2). 25 Immobiliser3). Jetta (2010-)4). GTI
		SKODA
		VW
		BENTLEY
		SEAT
	Program remote	AUDI	1). 09 Central control (CANBUS)2). 09 Central control (UDS)3). 35 Central lock (KWP1281)3.1). Type 1 3.2). Type 2 4). 46 Central comfort module (KWP1281) 4.1). Type 1 4.2). Type 2 5). 46 Central comfort module (KWP2000) 6). 46 Central comfort module (CANBUS)
		SKODA
		VW
		BENTLEY
		SEAT
	ECU Synchronization	AUDI	1). Imm21.1). Replace the engine ECU1.2). Replace the immobilizer ECU2). Imm3 2.1). Replace the engine ECU 2.2). Replace the Dashboard 3). Imm3.5 3.1). Replace the engine ECU 3.2). Replace the immobilizer ECU
		SKODA
		VW
		BENTLEY
		SEAT
VW	4th/5th Immobilizer system	4th Immobilizer system	1). CDC+24C322). NEC+24C323). 9S12XHZ51 (Golf6 MM7-2011) 4). NEC+95320 5). NEC+95320 (HohnSon/JCI) 6). NEC 35XX 7). NEC+24C64 8). NEC+C64 Color screen 9). NEC+24C64(2013) Blank screen10). NEC+24C64 (2013) Color screen 11). NEC+24C64 (2015-) 12). A1/Q3NEC+24C64 (-2014) 13). Magotan/CC 14). A6L/Q7 15). AUDI A4R8 (2005-) 16). AUDI A4R4 (-2004) 17). AUDI A3/TT/R8
		5th Immobilizer system	1. Read anti-theft data2. Display anti-theft data3. Generate dealer keys4. Learn the key 5. End the key learning mode 6. Unlock OEM key
		A8/Phaeton/Touareg/Bentley( 46 chip)	1). Upload data2). Download data3). Generate dealer key4). Learning key 5). Read PIN code and CS code (OBD) 6). Get the seventh byte of CS code
		Porsche (2007-2010)	1). Upload data2). Download data3). Generate dealer key4). Learning key 5). Read PIN code and CS code (OBD) 6). Get the seventh byte of CS code
	MQB platform		1. Read anti-theft data 2. Generate dealer keys 3. Learn the key4. Reset the instrument
	Online key matching	4th immo 96-bit key (copy/learn)	1). Upload data2). Download data3). Copy key4). Generate dealer key 5). Learn key (UDS) 6). Unlock key 7). Online mode
		MQB Online Key Matching (Add/All Lose )	1). Upload data2). Download data3). Generate dealer key4). Learn key 5). Online mode
		5th Key add	1). Upload data2). Download data3). Generate dealer key4). Learn key 5). Online mode
		5th Key all lose	1). Upload data2). Download data3). Generate dealer key4). Learn key 5). Online mode
	Key programmer		1. Generate a special chip2. Read and write 48 chips3. Read and write 46 chips4. Read the remote control frequency
	Read and write ECU		1). J518 (1LWH/3L40K) (-2010)2). J518 (0L01Y) (2010-)3). BCM2 (D70F3381/3634) 4). AUDI-ESL

VXDIAG VCX SE Benz License Expired Solution

Here share the solution to resolve VXDIAG VCX SE Benz license expired problem.

Problem:
Hello, I’m getting again that license expired… Can you help me please? I try to update the license, but it prompts “update license failed. Retry! Error Code: 0”. Can you explain to me exactly how to do?

Obd2tool.com engineer replied:
You should connect the VCX SE BENZ interface firstly, and then update license in VX Manager. You need to update it every 60 days.

The customer’s feedback:
I’ve just done. It works! Thanks!