Aeration and aeration and oxygenation with aeration agent

The tube expands when inflated, the micropores open, and when the air stops, the micropores are closed. Since there is no ready-made pipeline equipment, it needs to be selected in the market.So how much do you know about the aeration tube of the aerator? Today, I have sorted out some problems about the aeration tube in use.. When the water level deepens, it shows its advantages. It can prevent clogging better than the rigid tube, but the micropores are difficult for the tube to lose its elasticity after aging Open. Connect the joint on the PVC main pipe with the aeration pipe with a hose. So the quality of the pipe is very important.

It should not be tied too tightly. 1 Thereby, the stocking density can be increased, the feeding intensity of the breeding objects can be increased, the growth can be promoted, the yield per mu can be greatly increased, and the purpose of increasing Paddle Wheel Aerators Manufacturers the breeding income can be fully achieved. Three-phase four-wire cables should be used. To increase the amount of dissolved oxygen in the water. Such as vortex air pump, displacement blower. supplies aquatic aerators. The starting voltage of the aerators should be within the specified range. The air pump should also have an air filter device during the working process.

There are two main ways to improve the effect of aeration: aeration and aeration and oxygenation with aeration agent. Reasonably determine the startup and operating time of the aerator. The aerator is a device that drives working parts through a power source such as an electric motor or a diesel engine, so that the oxygen in the air is quickly transferred to the aquaculture water. Every winter, the whole machine should be derusted and repainted for maintenance.

The above is all the contents of the aerator introduced for you today, I hope to bring you some help. The correct use and maintenance of aquatic aerators is also an important part of improving the aeration effect. At ordinary times, care should be taken to remove the moss and algae debris on the impeller and stomata to ensure that the design parameters of the impeller remain unchanged, and often check whether the working condition is good. Microporous aeration is to arrange the polymer microporous oxygen aeration tube at the bottom of the water and perform aeration from the bottom of the water so that the dissolved oxygen can be evenly distributed throughout the water body.

Aquatic product aerator describes the algae removal method of water quality treatment

Blue algae blooms. The other is It is formed by the lack of nutrients in the water body, such as oligowater, clarified water, and moss water. The rust-colored oil film in the pond is often caused by too much Euglena sanguineus, and the pink-green oil film is often caused by too much Euglena platyphylla. After they die, they produce dinoflagellate toxin, which poisons the fish to death. 2. Cyanobacteria blooms are common and difficult to improve water quality during freshwater aquaculture. It is not advisable to spray drugs to kill cyanobacteria in the whole pond to prevent hypoxia and cause poisoning of the aquatic products.

Aquatic product aerator describes the algae removal method of water quality treatment. Use copper ion-containing preparations or strong chlorine essence to spray in the leeward area to kill part of the blue algae in the water. Change about 20 cm of surface water for several days to reduce the concentration of cyanobacteria and eliminate excessive harmful substances in the water. 1. Choose to replace part of the upper water in the morning on a sunny day to promote the release of fertility in the water body and increase the fertility of the water body. The improved method is to use Baiduqing in the morning, and then use Guardian every four hours, and then increase the amount of algae probiotics, and then use potassium dihydrogen phosphate, dichaeline or nitrazine after the next day, and pay attention to adding new water to introduce good algae Kind.

This can be implemented by increasing the water exchange volume or frequency to adjust the nitrogen in the pond water: The phosphorus ratio controls the occurrence of cyanobacteria. The redness of the water caused by too much polydinium algae and Ceratodinium automatic fish feeder algae is commonly known as red water. Add new water Cryptomeria species, and pay special attention to turning on aerators and preparing aerobic powder and particles for emergency.

During the high-temperature breeding period, try to reduce the excessive organic matter in the pond. Red water caused by algae pouring. For example, when the water temperature and pH value suddenly change, a large number of them will die and make the organic matter richer, thus making the water body appear black. It is difficult to achieve results using only one method. The dominant species are Oscillatoria and Cellulosae., commonly known as lake indigo and copper rust water. cause a large number of algae deaths in the pond, commonly known as algae, which causes the pond water to become red.

This type of water quality often occurs in newly excavated ponds or ponds with insufficient fertility retention, and in static water bodies with little water exchange.. Red water formed by non-inverted algae. This type of water quality often occurs in high-humidity seasons, not only in conventional breeding ponds, but also in breeding ponds for famous species such as river crab and Macrobrachium rosenbergii. Once this type of color appears in the downwind area of the pond, it indicates that the pond is lacking in fertility, and appropriate fertilizer should be selected according to the fertilization situation of the pond. The third is the poor water quality caused by the rapid change of environmental conditions, such as algae and red water