Netgear EX6100 Extender Firmware Update Fails? Let’s Fix!

Not being able to perform the EX6100 firmware update process is one of the major issues that every 3rd Netgear extender user is worried about. Are you also bothered by the same issue? Need not to worry! Let’s ease out the worry lines on your forehead! Walkthrough the Netgear extender troubleshooting steps mentioned in this article and learn how to resolve the issue in a jiffy. Let’s start over!

Reasons: Why Can’t You Perform Netgear EX6100 Firmware Update?

There can be a number of reasons that might be stopping you from updating the Netgear EX6100 firmware. A few of them are highlighted below. Scroll down a little!

• Loose or improper cable connection
• Poor connection between the EX6100 extender and router
• Slow or no internet connection
• Your Netgear EX6100 extender is surrounded by interference-creating devices
• The Ethernet cable you’re using is damaged or worn out
• Using mywifiext.local on a Windows computer instead of www.mywifiext.net

Now that you know the reason why aren’t able to update the firmware of your Netgear EX6100 extender, follow the steps outlined underneath to troubleshoot the issue. Keep scrolling down!

Things to do When Netgear EX6100 Firmware Update Fails

Fix 1: Check Your Internet Connection

One of the biggest yet major reasons why you’re facing issues while trying to update the firmware of your EX6100 is a weak or poor internet connection. To fix the issue, ensure that the extender is securely and properly connected to your router using an Ethernet cable. Apart from this, contact your ISP and confirm that there isn’t any issue from his end, all your pending internet bills are clear, and the device provided by him is up-to-date. 

Fix 2: Select the Right Firmware Version for Your EX6100

Most of the time – 4 out of 5 users end up facing the Netgear EX6100 firmware update failure issue because they choose the wrong firmware version. Thus, make sure that you’re downloading only correct version of firmware for your extender model i.e. EX6100. Navigate to the official site of Netgear to select the correct firmware version and for on-screen instructions.

Fix 3: Keep Your EX6100 Away from Electronic Devices

Have you placed your Netgear EX6100 extender near to interference-creating WiFi devices? If so, then you’ve found the reason why you’re unable to perform Netgear EX6100 extender firmware update. To troubleshoot the issue, make sure that you place your EX6100 away from baby monitors, Bluetooth speakers, and the reach of neighboring WiFi networks. 

After relocating your WiFi extender, try to access Netgear EX6100 setup page and check whether you’re able to perform firmware update process or not. If not, then it’s high time that you reset your Netgear EX6100 extender back to the factory default settings. 

Fix 4: Reset Your Netgear EX6100

Resetting your Netgear EX6100 extender will wipe out all the settings/ changed made by you. So, its better you take the back up of the extender settings. Here’s how to reset Netgear extender. Continue reading!

• Disconnect your Netgear EX6100 extender from all the connected devices in your home, including router.
• Then, look for the Reset hole on your Netgear EX6100 extender.
• Once found, press it using an oil pin, paper clip, or any thin and pointed object.
• Hold the Reset hole for some time and release it. 

After resetting your EX6100, perform the Netgear extender setup process again and try to update its firmware. 

The Bottom Line

This was all about our article to troubleshoot the Netgear EX6100 firmware update fail issue. We hope that the steps listed above helped you out in a great manner. We are eagerly waiting for your feedback. On the off chance, if the issue persists, don’t hesitate to lay all your queries on us via comments.